Saturday, May 21, 2016

DeWalt Scroll Saw DIY Utility Table from Charles Stopczynski

- I received an email from Charles a few days ago. He showed me a picture of a utility table that he and several members of his woodworking club have built for their DeWalt saws. I thought it was so interesting that I ask him to do a little write up so I could share it with all of you. I think the concept could be used to make something similar for other saws. Thanks Charles.

                                More pictures below the article.             

EASY  TO  MAKE  UTILITY TABLE
FOR:  De WALT  &  DELTA SCROLL SAWS


Many friends in the Gwinnett Woodworkers Association (Gwinnett County, GA)  and meself are scroll sawyers.  Most use the above saws.  Steve recently had an article on making of a tool for the top blade binding screw.  Seeing the photo of the tool it was clear to me there was no utility table.   I knew many scroll sawyers out there who have these saws could benefit from using one under their saw.  Having recently come over to the yellow side, and recently built a utility table, I decided to tell Steve about it.
Frankly, I was surprised that word hadn’t gotten around.  They’re great to catch little pieces of wood that fall from the cutting table, tools like your precious blade square, blades etc.  So, here goes.

The pattern for the utility table is right on your saw, the saw table itself is the basic pattern.  The table detaches very easily, remove the table locking knob, hold on, its cast iron and heavy.  Here is where you might want a second set of hands to help, also when re-installing it.  Don’t want to drop it $$*%$$$ ouch!   The screw that the knob attaches to might slip to the rear, just reach back and push forward when re-attaching, the table.  There is a washer in behind the knob as well.   (Note) you will need to be sure your table and blade is square before cutting.

Materials List:

         •     ¾” table material, about 24” x 36” such as plywood, MDF etc.
         •     3, 5/16 x 3” carriage bolts, 3 washers, 3 nuts, 2 acorn nuts (option)
         •     Approximately 80” of edge material, such as laminate, plastic, metal, Masonite®™ or other
         •     #4 x ¾” FH wood screws
         •      self-made tracer-spacer tool, ¼” scrap plywood, approximately 2” x 6” see photo.

Making a tracer spacer tool is easy.   Scribe a centerline lengthwise.   2” from one end drill a hole, just enough to accommodate a Sharpie®™ standard fine marker without wobble.

The material chosen for the saw table was a “sink cut-out”, which was already on hand.  It was from a household double kitchen sink, ¾” particle board with laminate on one surface about 24” x 36”.  Many other materials would also make a suitable table.  This particular design gives you a table that is wider than the saw table to catch falling objects, reasonable roomy, but not too big.   The design can be adjusted to suit your need.

Place the scroll saw table face down upon the laminate side and trace the outline of the curved parts of the table using the tracing-spacing tool and marker.   Decision time:  How much wider than the cutting table do you want your utility table.  I made mine 2” wider (on each side) therefore a total of 4” wider, hence the 2” setback on the tracer spacer tool.   I chose to continue the table all the way to the back of the saw stand.  This rear portion was made 10” wide, starting some distance forward of the rear of the table tracing.   A square was used, lines drawn from what would become the back of the table forward to meet the expanded outline of the saw table made with the tracer-spacer tool.  Here’s an opportunity make design changes to fit one’s need.  Cutting out the table while clamped to a workbench, a jig saw (heaven forbid) was used with a new blade suitable for cutting laminates, this particular blade cuts on the downstroke.  The result was a cut super clean.  Sand any irregularities.

Remove the saw from the stand, assuming you use the manufacturers saw stand.  In the rear center a 3/8” by 1” slot was cut to accommodate the rear bolt.  This was the starting point of mounting the utility table.  Place saw onto the sub-table.  Remember, here you have a decision to make as to front to rear placement of the sub-table.  I chose to make the front of my sub-table square with the front edge of the saw table.   The rear of the saw was first bolted into place, snug but not fully tight to allow left to right adjustment.   Use a square to adjust left to right sides measuring the distances on sub-table top to edges until centered, measurements were taken outward next to the front mounting holes for the saw.  Mark centers of the two front mounting holes.  Drill  a small pilot hole, then use a 3/8” drill to bore the two mounting holes.  No improvement would be complete without the mandatory trip to the hardware store.  The original mounting bolts you will now discover, are too short.   Use the 3, 5/16 x 3” Carriage bolts.

Washers to protect the saws finish and the casting itself were used.  Acorn nuts on top of the exposed threads in the front were added to save finger tips and finger nails from exposed thread edges.

Scrap laminate can be used to form the edge of the utility table, things tend tofind their way to the floor while sawing.  1/8” Masonite®™ was chosen for this table.   80” will be more than sufficient.  A 2” width was chosen for this particular table.  Once again it was learned that Masonite®™ bends some but it does not like tight bends.  The edging was installed using single piece covering most of the curved section. Two more short lengths down  each side and a 10 ¼” piece across the rear.  All edging was attached with #4 x ¾” countersunk wood screws.

This is the end of the daily posts. Keep scrolling for lot's more scrolls saw fun!






https://www.bearwood.com/
Bear Woods has been around since 1987 serving our hobby. They offer a wide range of craft products including Pegas scroll saw blades, clock inserts, toy parts, workshop supplies and much more. In my ten years of writing the Scrollsaw Workshop blog I have never received a complaint about Bear Woods. I get thousands of email a month so that's saying something about their customer service and quality products. Please support the people who support our hobby. Click now and visit Bear Woods.

Heritage Wood Specialties. Scroll saw ready boards!


Heritage Wood Specialties is a nationally recognized supplier of superior quality hardwoods to fine woodworkers across the US and Canada. Novice hobbyists and experienced enthusiasts alike can enjoy the high quality woodworking materials and kits available from Heritage Wood Specialties. Great source for scroll saw ready boards.

Seyco

http://seyco.com/
Seyco began business in 1986 with the goal to supply the best customer support and quality products in the scroll saw industry. I have worked with Seyco on many occasions and I can tell you they are simply the best. Please do yourself a favor and click the image above. Steve Good

Free Pattern Catalog. 1000's of free patterns.

http://www.stevedgood.com/catalog/

Thousands of FREE scroll saw patterns. No registration or signup required.

The projects form these patterns can be sold without restrictions. The patterns cannot be sold.

Click here for the Free Online Catalog.

-

Wooden Vases on the Scroll Saw Book $12 Each

http://www.stevedgood.com/woodenvases.html
Each digital book is available for download immediately after payment.
The books are $12 per edition and contains eight unique patterns each.
Watch the following video to see how easy these beautiful scroll saw vases
are to make. 

Order the $3 pdf Catalog

This is a PDF of all the patterns in my free catalog. It is for Windows only and has a program to automatically download the pattern to your computer. Please watch the video below before you order. Click the picture to order.
http://www.stevedgood.com/swpd/swpdorderpage.html
You do not need a PayPal account to order. At the bottom of the PayPal page is a button that will allow you to pay with a credit card. After successful payment click the Return to Merchant button for the download.

Stencil Printer 1.7

Stencil Printer Instruction Video.

The Scrollsaw Workshop Stencil Printer 1.7 is my latest software for creating patterns. It will create key chain fobs, desk name plates and more. Click the image above to download the latest version. It is free to use donationware. This software is for Windows PC only.

Scroll Saw Pattern Printer update 1.1

Scroll Saw Pattern Printer update 1.1
Download the Free Scroll Saw Pattern Printer Version 1.1. Create name patterns in seconds. Windows PC only.
Download Version 1.1
Please consider a $5 donation for The Scroll Saw Pattern Printer v1.1.

Scroll Saw Keychain Pattern Maker

Use the Scroll Saw Keychain Maker to start a small keychain business. Build yourself a nice display and make up severl keychains with common names. Sell at craft shows, on Ebay or at work. Everyone needs a keychain. Take custom orders. Heck just make them and give them away as gifts. It's all made easy with the Scroll Saw Keychain Maker. Watch the video demonstration then download the file below and get started with the fun.
The following link will start the download process. After the file download is complete just click the setup file and the program will be installed. Please consider a $5 donation for the program.

Download the Oval Keychain Pattern Maker.

Enjoy designing and printing these great personalized key chains. Give them as gifts, make them for fun or sell them at craft shows. It's easy, just watch the video demo then download and install the program. You will be designing these fun projects in minutes. Windows PC only.
Download the Free Oval Key Chain Pattern Maker. Create Oval key chain patterns in seconds.
Download Version .9a
Please consider a $5 donation for The Oval Key Chain Pattern Maker.

T-Shirts and More.

T-Shirts and More.
Show your love for the hobby and support the Scrollsaw Workshop. Safe and secure order fullfilled by CafePress. Take a look. You are sure to find something you like. CLICK THE IMAGE to visit the store.

The Lifter

Papa's Custom Patterns.

www.papasworkshop.net

Philip Lowndes Noah's Arc Pattern Available. Watch the video below.

This video is from Philip Lowndes. He is the designer of this beautiful Noah's Arc puzzle pattern. If you would like the pattern follow the link below.
Buy This Wonderful Heirloom Puzzle Pattern

Think Safety

Remember to keep the safety of yourself and others in your work shop in your thoughts at all times. Always wear eye and ear protection. Follow all the manufactures warnings that came with your power tools. If I demonstrate something on this web site that you don't feel is safe, don't do it. Your safety is your responsibility. Fingers are handy things, try to keep all of them.
__________________________
Disclaimer:
The Scrollsaw Workshop Blog is in no way affiliated with or sponsored by Scroll Saw Woodworking and Crafts Magazine formerly (Scroll Saw Workshop Magazine) or it's publisher Fox Chapel Publishing.

Scroll Saw Woodworking and Crafts